Get a Quote
Social Media

How is freight calculated for part-load (LTL) road transport?

Last updated:

Short Answer — Part-Load Freight Calculation

In part-load transport, freight is calculated on the chargeable weight. The actual gross weight, the weight equivalent of the volume (common ratio 1 m³ = 333 kg) and the equivalent of the loading metres (1 ldm ≈ 1,750–1,850 kg) are compared, and the largest is used. This figure is multiplied by the route's unit price per 100 kg, and surcharges are added separately.

Why is weight alone not enough?

A truck trailer sells three resources at once: payload capacity, internal volume and floor space. A standard trailer is about 13.6 m long with an internal width of 2.45 m; because of the legal gross weight limit, it takes around 24–25 tonnes of cargo. A light but bulky load (foam, furniture) fills the trailer without using up the tonnage, while a non-stackable machine takes up a long stretch of floor with little volume. The carrier therefore measures every load in three ways and invoices the largest. This value is called the chargeable weight.

How are the three measures calculated?

  • Actual weight: Gross kilograms including pallet and packaging; net weight is not used.
  • Volumetric weight: The m³ obtained from length × width × height (in metres, measured at the outermost points) is multiplied by the conversion ratio. The most common ratio in the European road market is 1 m³ = 333 kg; some carriers use 250–300 kg.
  • Loading-metre weight: Loading metres (ldm) = (length × width) / 2.4, and 1 ldm is usually multiplied by 1,750–1,850 kg. A Euro pallet (1.2 × 0.8 m) equals 0.4 ldm, an industrial pallet (1.2 × 1.0 m) 0.5 ldm. For stackable loads, ldm is calculated only on the number of pallets standing on the floor.

Worked example

Six Euro pallets, 1,800 kg gross in total, with conversion ratios of 333 kg/m³ and 1,750 kg/ldm.

CaseActual weightVolumetric weightldm weightInvoiced
Pallets 1.6 m high, non-stackable1,800 kg9.22 m³ × 333 = 3,069 kg2.4 ldm × 1,750 = 4,200 kg4,200 kg
Pallets 1.2 m high, double-stackable1,800 kg6.91 m³ × 333 = 2,302 kg1.2 ldm × 1,750 = 2,100 kg2,302 kg

The same weight of cargo travels on roughly 45 percent less chargeable weight once the packaging height and stacking permission change. The invoiced value is multiplied by the route's “per 100 kg” unit price: 42 units for 4,200 kg, 23.02 units for 2,302 kg. Most tariffs also apply a minimum weight or a minimum freight charge.

Which items can be added to the freight?

  • Fuel surcharge and periodic road, bridge and ferry charges
  • Collection from and delivery to an address (instead of depot delivery)
  • Customs declaration, T1 or TIR carnet formalities
  • Dangerous goods (ADR) cargo, temperature-controlled transport, or the need for a drop-side or curtain-sider vehicle
  • Waiting time at loading and unloading, appointment-based delivery

Common mistakes

  • Under-declaring pallet height: Cargo re-measured at the depot leads to the invoice being changed afterwards.
  • Declaring “stackable” but sending packaging that cannot take a load on top: A pointed lid, a fragile carton or a “do not stack” mark on the label makes the cargo non-stackable.
  • Underestimating long items: A 6 m bundle of pipes may be narrow, but if nothing else can be placed beside it, it may be counted as ldm across the full trailer width.
  • Not asking about the conversion ratio: Even if two quotes have the same price per kilogram, different ratios change the total. What to provide when requesting a quote is listed in the entry on information needed for a road freight quote.

How does Voltim Global help with this?

In Voltim Global's part-load transport service, chargeable weight is calculated from the dimensions, weight and stacking information declared by the shipper; this is why pallet height and stacking permission are confirmed in writing before loading. The same measurements can also be used to compare which consignment would travel more cheaply as a full truckload rather than part-load (LTL).

Frequently Asked Questions

Is the courier “desi” calculation used for part-load truck cargo?
No. Desi is a method used in courier and parcel transport that divides the volume measured in centimetres. In part-load road transport, volume is converted into weight via m³ and floor space via ldm. For small cartons, the difference between the two methods is compared in the entry on international courier vs part-load truck.
What happens if the cargo turns out bigger or heavier than declared?
The carrier or cross-dock depot re-measures and re-weighs the cargo; if the result exceeds the basis of the quote, the freight is recalculated on the new chargeable weight. If the difference is large, there may be no room left on the vehicle and the cargo may be held for the next departure. Measurements should therefore be taken at the outermost points, including the pallet, and the weight supported by a weighbridge ticket.

Published: 19.11.2026 · Voltim Global